Next step, do a detailing.

To Calculate LMTD, we need to understand the flow and type of process (Isothermal or not)

Generally we have complication, when either of fluid is showing isothermal characteristics. see the following variation.

Two fluids are separated by a heat transfer surface (wall), these fluids ideally do not mix, and there are no moving parts.In this blog the thermal design theory of recuperates is presented. In a heat exchanger, when hot and cold fluids are maintained at constant temperatures of Th and Tc as shown in above Fig(a)..The driving force for overall heat transfer in the exchanger, referred to as mean temperature difference (MTD), is simply Th-Tc.

Such idealized constant temperatures on both sides may occur in idealized single-component condensation on one fluid side and idealized single-component evaporation on the other fluid side of the exchanger. However, a number of heat transfer applications have condensation or evaporation of
single-component fluid on one side and single-phase fluid on the other side. In such cases, the idealized temperature distribution is shown in Fig(b) and (c)

The First major step in Thermal design, is to understand the assumptions that are considered while we disign the heat exchanger, but we forgot to understand them, they are:-

1. The heat exchanger operates under steady-state conditions [i.e., constant flowrates and fluid temperatures (at the inlet and within the exchanger) independent of time].

2. Heat losses to or from the surroundings are negligible (i.e. the heat exchanger outside walls are adiabatic).

3. There are no thermal energy sources or sinks in the exchanger walls or fluids, suchas electric heating, chemical reaction, or nuclear processes.

4. The temperature of each fluid is uniform over every cross section in counter flow and parallel flow exchangers (i.e., perfect transverse mixing and no temperature gradient normal to the flow direction). Each fluid is considered mixed or unmixed from the temperature distribution viewpoint at every cross section in single-pass cross flow exchangers, depending on the specifications. For a multi pass exchanger, the foregoing statements apply to each pass depending on the basic flow arrangement of the passes; the fluid is considered mixed or unmixed between passes as specified.

5. Wall thermal resistance is distributed uniformly in the entire exchanger.

6. Either there are no phase changes (condensation or vaporization) in the fluidstreams flowing through the exchanger or the phase change occurs under thefollowing condition. The phase change occurs at a constant temperature as for a single-component fluid at constant pressure.

7. Longitudinal heat conduction in the fluids and in the wall is negligible.

8. The individual and overall heat transfer coefficients are constant (independent of temperature, time, and position) throughout the exchanger, including the case of phase-changing fluids in assumption 6.

9. The specific heat of each fluid is constant throughout the exchanger, so that the heat capacity rate on each side is treated as constant. Note that the other fluid properties are not involved directly in the energy balance and rate equations, but are involved implicitly in NTU and are treated as constant.

10. For an extended surface exchanger, the overall extended surface efficiency is considered uniform and constant.

11. The heat transfer surface area A is distributed uniformly on each fluid side in a single-pass or multi pass exchanger. In a multi pass unit, the heat transfer surface area is distributed uniformly in each pass, although different passes can have different surface areas.

12. For a plate-baffled (1–n) shell-and-tube exchanger, the temperature rise (or drop) per baffle pass (or compartment) is small compared to the total temperature rise (or drop) of the shell fluid in the exchanger, so that the shell fluid can be treated as mixed at any cross section. This implies that the number of baffles is large in the exchanger.

13. The velocity and temperature at the entrance of the heat exchanger on each fluidside are uniform over the flow cross section. There is no gross flow maldistribution at the inlet.

14. The fluid flow rate is uniformly distributed through the exchanger on each fluid side in each pass i.e., no passage-to-passage or viscosity-induced maldistribution occurs in the exchanger core. Also, no flow stratification, flow bypassing, or flow leakages occur in any stream. The flow condition is characterized by the bulk (or mean) velocity at any cross section.

Question??? So many assumption… still we are ‘designing’ a heat exchanger with Guarantee on performance!! sure we are Engineers 😉

Following Table will show the impact of various parameters on design of heat exchanger.
(NTU stands for number of transfer unit, and alternate to LMTD method)

https://sumitwaghmare.com/about-me/

Comments (8)

  1. Reply

    Howdy I am so delighted I found your blog page, I really found you by accident, while I was looking on Yahoo for something else, Nonetheless I am here now and would just like to say kudos for a incredible post and a all round exciting blog (I also love the theme/design), I don’t have time to look over it all at the moment but I have book-marked it and also added your RSS feeds, so when I have time I will be back to read a lot more, Please do keep up the excellent job.
    Electric steam boiler

  2. Reply

    Thanks for another wonderful article. The place else may just anybody get that kind of info in such an ideal means of writing? I have a presentation next week, and I am at the search for such information.

  3. Reply

    My partner and I absolutely love your blog and find many of your post’s to be exactly I’m looking for. can you offer guest writers to write content for you? I wouldn’t mind writing a post or elaborating on a number of the subjects you write regarding here. Again, awesome web site!

Leave a comment

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.